Motherboard Damage
Main board (motherboard) is the circuit board where a variety of interconnected electronic components such as microprocessors and memory (RAM, ROM, BIOS) and other controller chips and commonly abbreviated to mobo said. Symptoms and how to cope with a damaged motherboard :
1. Total dead
Check the power supply. In the state of the power cord from the power supply off, disconnect the cable socket mounted on Mainboard Atx1. Once detached, attach it back to the power cable, plug / cable shortkan green with a black cord, check that the power supply fan spinning? If the spin is a good power supply. Unplug the cable connections were Atx1 and reattach cables to the motherboard.
Check the Clear CMOS Jumper, whether in Clear or Free position,usually when a new motherboard, the position of the CMOS jumper on the Clear position.
Check the IC Chipset plugged in and on the Switch On, whether or not the excessive heat, over-heat means the chipset is already damaged. CMOS ICs for parts so far not sold free. check also whether the switch on its functioning. Unloading the Motherboard carefully, you try to clean the wear thinner, if you can not use thinners bottle in tin. After you dry clean. Replace the IC regulator which is located around the ATX power socket on the motherboard. Replace the capacity Elco 1000 s / d 3300 uF / 10Volt located around the ATX power socket on the motherboard. Be careful to make sure the component loading plug the power cablenot connected to the mains.
2. Computer Ok, But Not Appearing In Monitor
You try to watch and listen for whether there is sound or beep sound. If any, damage there is usually at the processor, memory and VGA.
Check the Processor, you try to hold the coolant is excessive heator cold? If overheating is the processor fan is not working properly then you change, but if cool means the processor does not work alias is broken.
Check the memory, usually when the memory is damaged audible beep on the speakers 3 times. Are turned off, pull the memory clean the pins using a pencil eraser to clean, then reinstall. If it means there's still broken one of his damaged IC.
Check your VGA card, unplug the VGA card, in the dead / off, you try to press, there are less chances you get or try to wash the feet /her pin. If the VGA card using the fan, clean the fan. If it still does not appear you try to check lest the monitor that is not a flame, to ensure that damaged the monitor or CPU, you try to press keys on the keyboard Numlock, whether Numlock lights her flame or not. If the flame is damage to the CPU.
Is the standard that I fix computers, I always clean it from dust,whether it be the motherboard, memory, cdrom, floppy disks, etc.,because it is so what else could affect the computer in a dirty / oldis not cleaned. But you must be careful in the proceed and do not rush.
3. Hang And Often Off / Restart (Reset) Himself
Check the Power Supply, try using another power supply if it still restarts itself or hangs. If after replacement power supply turns normal / good, power supply means there is a problem. Change can be fixed if only because I am not sure whether it is still able to function properly, because the power supply is a vital component. Especially for the current price very cheap power supply, I suggest changing it.
Check whether there is virus, anti-virus program should always be installed and enable auto protect her. I used to use Kaspersky Internet Security Anti-virus. You should frequently update your antivirus because if there is a new variant virus, your anti-virus willdetect at once eliminate the virus.
At the moment there hangs and bluescreen messages such as"error vxd at address ...", there is usually a problem in memory.Clean the memory is like a step above. Try to reinstall Windows. If it still hangs / restart itself you try to check the motherboard, you notice physical changes in particular components of Elko /capacitors, which are writing a black round capacity between 1000uf/10Volt s / d 3300 uf/10 volts, usually seen, if the damage visiblebloating / swelling and remove fluid or rust.
CMOS Checksum Failure (Low Battery)
A message appears CMOS failure (damage to the CMOS battery, replace battery) Setting the date, time and other configurations in the BIOS to change (After replacing the battery, did reset the settings in the BIOS).
0 komentar:
Posting Komentar